HIFI listening room and home studio: which piece goes in each spot

Quick answer: in a listening room or home studio, sound is absorbed where it interferes and diffused where it is desirable for the room to retain vitality. Low frequencies are treated in the corners using a bass trap like ELYPSIUM; early reflections from side walls and ceiling using absorbers (HÍBRIDO or panels); and the wall behind the listener, if far away, using diffusers (4×4 DIFFUSER or 14×7 DIFFUSER). Below you will find which element goes in each position and what each one measures in the laboratory.
What happens to sound in a listening room?
Good speakers in an untreated room sound worse than they actually are. It is not the equipment's fault: it is the room, which returns sound in three ways that are immediately audible:
- Booming bass: some bass notes sound too loud while others almost disappear, changing even if you move slightly on the sofa.
- First reflections: sound bounces off side walls, ceiling, and floor, reaching your ears right after the direct sound. They blend together, smearing the stereo image and making it hard to localize vocals and individual instruments.
- Back wall reflections and flutter echo between parallel walls: sound returns from behind or bounces back and forth between two facing walls, leaving a metallic tail after every transient.
- If, in addition, the whole room suffers from echo like an empty corridor, the problem is reverberation: we explain this in "How to eliminate echo from a room".
Each of those problems has its place in the room, and that is why each piece has its own.
Absorb sound or diffuse sound?
A sound-absorbent keeps part of the sound that reaches it: the room sounds drier and clearer. A diffuser does not keep the sound: it distributes it in many directions, so that a strong reflection becomes many weak ones and the room keeps its life. A room treated only with sound-absorbent ends up sounding dull; one treated only with diffusers keeps booming in the bass. In a listening room, both are combined.
Which element goes in each location?
Here is the table to get started. The αw summarizes in a single number what a panel absorbs (from 0 to 1), measured in a laboratory; it is only given where an absorption test report exists.
| Location | Piece | Purpose | αw (tested) |
|---|---|---|---|
| Corners, on the floor | ELYPSIUM | Bass trap: where it performs best in low frequencies | Measured per piece (low frequencies table) |
| On the floor, in the middle of the room | ELYPSIUM | Absorb bass, midrange, and treble without touching the walls | Measured per piece (low frequencies table) |
| Side Walls, at first reflections | HÍBRIDO on the wall | Absorb the reflection | 1.00 · TECNALIA B2019-LACUS-IN-83 I |
| Front wall, behind the speakers | WB HP on the floor or HÍBRIDO | Absorb bass, midrange, and treble | 1.00 · TECNALIA 110259-7 (WB HP) |
| Ceiling, at the first reflection point | 40 mm adhesive ILUCS panel | Eliminate ceiling slap echo | 0.85 (H) · TECNALIA B2018-LACUS-IN-27 II |
| Wall behind the listener, if far away | 4×4 DIFFUSER or 14×7 DIFFUSER | Break up reflection without deadening the room | Not applicable: it is a diffuser |
| Ceiling, behind the listening area | 4×4 DIFFUSER or 14×7 DIFFUSER | Distribute the sound reaching the ceiling | Not applicable: it is a diffuser |
A rule that should not be skipped: ELYPSIUM, HÍBRIDO and WB HP do not go on the ceiling. ELYPSIUM goes on the floor, in the middle of the room or in corners; HÍBRIDO on the floor or wall; and WB HP on the floor. Diffusers do go on the ceiling and wall.
Why are bass frequencies treated in the corners?
In an enclosed room, low frequencies form standing waves: at some points they add together and boom, and at others they cancel out. That is why the same note sounds different depending on where you sit. All those waves have their maximum pressure in the corners, which is where a bass trap has more sound to absorb.
We measured it with ELYPSIUM in both positions. As it is a free-standing object and not a panel glued to the wall, the laboratory does not give an αw: it gives the square meters of absorption that each piece adds, band by band. One square meter of a material that absorbs everything adds one square meter of absorption; this allows direct comparison.
| ELYPSIUM, m² of sound absorption per piece | 125 Hz | 250 Hz | 500 Hz | 1000 Hz | 2000 Hz | 4000 Hz | Report |
|---|---|---|---|---|---|---|---|
| In the corners | 1.3 | 1.6 | 1.6 | 1.2 | 1.1 | 1.0 | TECNALIA B2019-LACUS-IN-83 III |
| In the middle of the room | 0.9 | 1.9 | 2.1 | 2.0 | 2.0 | 1.8 | TECNALIA B2019-LACUS-IN-83 II |
At 125 Hz, each ELYPSIUM in a corner adds 1.3 m² of absorption; in the middle of the room, 0.9 m². From 250 Hz upward, the reverse happens: it adds more in the middle of the room because sound reaches it from all sides. If low frequencies are the issue, place them in the corners; if you want distributed sound absorption without touching the walls, place them in the middle of the room.
Which sound-absorbent holds up better against low frequencies?
In mid and high frequencies, the three pieces in the table absorb maximum or nearly maximum sound. The difference lies lower down, where thickness dictates performance. This is the practical coefficient αp per octave, measured in a laboratory, for three of our pieces:
| Piece | Thickness | 125 Hz | 250 Hz | 500 Hz | 1000 Hz | 2000 Hz | 4000 Hz | αw | Report |
|---|---|---|---|---|---|---|---|---|---|
| Adhesive ILUCS panel, surface-mounted | 40 mm | 0.15 | 0.55 | 1.00 | 1.00 | 1.00 | 1.00 | 0.85 (H) | TECNALIA B2018-LACUS-IN-27 II |
| HÍBRIDO, on the surface | 108–223 mm | 0.50 | 0.95 | 1.00 | 0.95 | 0.95 | 0.90 | 1.00 | TECNALIA B2019-LACUS-IN-83 I |
| WB HP, floor-standing against the wall | 140 mm | 0.65 | 0.95 | 1.00 | 1.00 | 1.00 | 1.00 | 1.00 | TECNALIA 110259-7 |
At 125 Hz, the 40 mm panel absorbs 0.15; the HÍBRIDO, 0.50; the WB HP, 0.65. For this reason, thick pieces go at the front and sides, where there are also low frequencies. On the ceiling, on the other hand, the 40 mm panel already eliminates bounce in mid and high frequencies: from 500 Hz its αp is 1.00.
Where do the first reflections land?
They depend on where the speakers are located and where you sit, so there is no fixed measurement. They are found using a mirror: sitting in your position, someone slides a mirror along the side wall and, wherever you see the speaker reflected, that is where the sound-absorbing element goes. Do the same on the other wall and on the ceiling.
What to put on the back wall?
It depends on how close you are to it. If the wall behind is far from your head, its reflection arrives later: that is where a diffuser works, breaking it into many weak reflections without taking life away from the room. If it is right behind your back, a sound-absorbing material is better, such as a HÍBRIDO on the wall.
The two diffusers in the range can be wall- or ceiling-mounted, and several pieces can be joined together to form a continuous surface:
| Diffuser | Measurement | Relief | Material | Where it goes |
|---|---|---|---|---|
| 4×4 DIFFUSER | 480 × 480 mm | blocks from 9 to 103 mm | solid pine wood | wall or ceiling |
| 14×7 DIFFUSER | 600 × 600 mm | cells from 13 to 53 mm | Fire-retardant MDF and solid pine | wall or ceiling |
An example: a rectangular listening room
Let us assume a rectangular room with speakers in front against the short wall and the armchair toward the center. One way to start, from front to back:
| Step | Where | What to install |
|---|---|---|
| 1 | Front corners, behind the loudspeakers | An ELYPSIUM in each corner, on the floor |
| 2 | The front wall, between the speakers | WB HP on the floor or HÍBRIDO |
| 3 | Both side walls, at the first reflection | One HÍBRIDO on each wall, located where indicated by the mirror test |
| 4 | The ceiling, between the speakers and the listening chair | 40 mm adhesive ILUCS panels, wherever the mirror indicates |
| 5 | The rear wall, if it is far away | 4×4 DIFFUSER or 14×7 DIFFUSER at ear height |
| 6 | Rear corners, if low frequencies continue to boom | Additional ELYPSIUM on the floor |
Afterward, listen to the same music as always from the exact same spot. If the vocal centres properly and low frequencies sound even from note to note, you are on the right track. If the whole room still sounds reverberant, general sound absorption is missing.
- To know how much echo the room has, band by band, and how much it decreases with each panel: «Calculate your room».
- And how much is recommended depending on the room type: «Recommended reverberation time».
What these elements do not do
- They do not isolate from the neighbor. Absorbing and diffusing improves how the room sounds inside; preventing it from being heard outside depends on the walls, doors, and windows.
- A diffuser does not eliminate bass boom: it redistributes the sound that reaches it. For bass, use the bass trap.
- They do not replace proper speaker and seat positioning. Moving either changes the bass significantly, and it is best done before treating the room.
- There is no single recipe for all rooms: the chart is a starting point, and the mirror and your ears do the rest.
Our pieces for this
Frequently asked questions
Can I install ELYPSIUM or WB HP on the ceiling?
No. ELYPSIUM is placed on the floor, in the middle of the room, or in corners, and is tested in both positions. HÍBRIDO goes on the floor or wall, and WB HP on the floor. On the ceiling, 4×4 and 14×7 diffusers and panels from the Ceilings range are used.
How many bass traps do I need?
It depends on the room size and how much low frequency boom there is. Each ELYPSIUM adds the square meters from the bass table; this allows you to calculate the required amount for your room. It is usual to start in the front corners and add to the rear ones if bass reverberation persists.
Does the same apply to a home cinema?
Yes. The three locations are the same: bass in the corners, first reflections on the sides and ceiling, and the back wall. With more speakers there are more first reflections: the mirror trick is repeated for each front speaker.
Do you install them yourselves?
ISINAC manufactures and supplies the pieces; installation is carried out by your installer, your distributor, or yourself, following the instructions in the manual.
Tags: sound absorption
/noticias/sala-escucha-hifi-acondicionamiento/